Because none of you asked....

Based on my last post I figure you should know what my prime choices are for my AR builds.

First off, KNS Precision for the pins and small parts and Wolff for springs. Both are well respected names in the industry and while I've not had a rifle yet that's hit a barrel life limit, so it's hard to say with certainty, but they've not failed or broken on me yet. Specifically, KNS's non-rotating trigger/hammer pin set got me started with them. I've replaced enough broken trigger pins on AR's at ranges that they became a fail point that I wanted to improve and KNS's NRTHP's were the answer to that.  And they were good enough that they lead me to looking to KNS for all the other pins and small parts.  Wolff springs, I selected them on advice from a 3 gun competitor that I used to work with. I've only ever had problems with one spring on any of my builds and that was one of Brownell's 50,000 round extractor springs that immediately didn't work out of the box, or Ziploc baggie as the case may be.  If a Wolff spring ever fails on me, I'll be sure to let y'all know.

I have used JP Enterprises Silent Capture Buffer Spring system and it's currently in my truck rifle. If you don't care about hearing the "Sproing of Freedom" when you shoot an AR, then I can recommend them.

For triggers, my first choice used to be Rock River Arms National Match Two Stage Trigger. This is a nice drop in two stage trigger with a smooth pull,  definite wall and good break. For around a hundred bucks it's good upgrade over the mil-spec GI trigger. I say used to be because I've been lured away and fallen in love with Geissele Automatics SSA-E trigger. It runs around a hundred dollars more than the RRA's trigger, but in my opinion it's worth every penny.  Again, it's a drop in replacement for the GI trigger and if you ever get a chance to shoot the two next to each other, you'll understand why it's my top pick for triggers.  Just keep in mind that I'm only looking at drop in replacements for the trigger. There are quite a few full customizable, fully adjustable triggers that will fit in the AR platform, but when you're looking at maintaining your rifle in the field, waiting 2-4 weeks for the replacement part to show up isn't my idea of a good idea.

Yes, I will always go with Magpul for the furniture on my rifles. Unless I'm looking at final weight as one of my considerations.  Then, and y'all will scoff at this, I go to ACE ARFX stocks. They're a good trade off between weight and ruggedness.  They'll survive being used as a brace when dropping into prone that I'd hate trusting a folding or collapsible stock to do.  They're a fixed stock, yes. But before you dismiss them. Unless 6 ft. you and 5 ft. 2 in. wifey are using the same rifle for home defense or you are actually in the military and have to adjust for varying levels of body armor a fixed stock is actually preferable in my opinion.

Now, these I'm going to list all together. Norgon's Ambi-Mag release, Teal Blue Bravo's PDQ Ambi Bolt Catch and any good ambi safety selector.  But not because they make the rifle more ambidexterous.  Yes, being able to shoot from either shoulder is a good skill to have. But because I want the only thing my off hand doing is getting the new mag and seating it.  Everything else can be done by the hand on the pistol grip without having to shift excessively.  Keeping my had there helps me maintain positive control of the rifle and the less fumbling, the less likely I'll be to... fumble... the rifle.

A good ambi charging handle like the Raptor is nearly a must these days of optics.  Often the optic sits right above the charging handle and being able to reach it can be problematic. Being able to reach up on either side to run it rather than having to try to reach around to hook both handles is a plus

For receivers, I've been a fan of Aero Precision's AR and .308 uppers and lowers.  They produce them in house and have an excellent QA department.  And I can hear y'all saying that so long as they're Mil-Spec, why pay more. There's a big difference between meeting the mil specs and using the mil specs as your starting point. When you start on .308 AR builds, you'll quickly learn that the .308 AR platform was never adopted by the US and therefore there is no mil-spec standard. DPMS's LR platform uses a lot of parts common with the AR-15. There are still differences, but they have more common parts with the AR-15 then the AR-10 system has. And Aero Precision uses the DPMS spec for their .308 AR's.  Again, maintaining in the field gets a lot easier when you don't have to have too many special parts for that one rifle.

Finally, as far as optics go, I have no recommendations.  I've used Trijicon, Burris, Aimpont, Vortex, and EOTech.  They've all worked, all held zero within abuse limits, and really made these tired old eyes look like a better shooter than they are.  The only caution I'd give you is you get what you pay for, so that 30 dollar red dot might look good to the bank account, but it may not look so good when it costs you standing in a shooting match or venison on the table.

Ian and Carl over at InRange TV have a great series on building an AR platform. They called it WWSD, or What Would Stoner Do, they approached their builds with weight as one of the primary considerations and they still ended up using a lot of the parts that I trust for my builds.  Although I swear their 3 gun rigs don't weigh half of what my truck rifle does.

Finally, these are my opinions and your mileage may vary. But these will give you a sense of peace of mind that your rifle will work and work when you need it to also.

NRAAM 2018 – Saturday Review Day

            Not that I had a plan for ANY of NRA AM, but I decided Saturday that I’d revisit some of the products that I’ve reviewed over the years. So, after getting my voting out of the way and figuring out some sort of plan at the press room, I tied my shoes (yeah, it’s about to get real) and hit the floor.  I planned to focus on some of my “go to’s” for my AR builds.  Namely, and in no particular order, Magpul, Adams Arms, AeroPrecision USA, KNS Precision, and Diamondhead. And as a bonus and since they were there, I thought a visit to Barrett was in order. Outside of those I would see how much time I had left that day.

            As some of you may know I’m a pretty staunch Magpul fanboi.  Aside from a couple of notable exceptions (cough, BAD lever, cough) they are spot on for putting out a product that is rugged, dependable, works out of the box, and is the best bang for the buck.  Talking to one of their reps that day, they’re being pretty cagey about what’s new on the horizon.  Although he did say they might be working on a magazine for the M14 platform. But that’s been a running gag for a while now.  Nothing on a Gen 4 for their mags, no word on any new AR or other rifle furniture. I can understand their reticence on talking out of turn, though.  They got a little burned when their Rem700 stock wasn’t perfect on it’s first release and the delays that resulted.  I’ve used the UBR on a couple of carbine builds, their PRS for a 22” precision based around BCM’s Mod 12 18” precision upper as well as their AR MOE rifle stock on an LR-308 build. Aside from the UBR and PRS being heavy and both those rifles ending up on the high end for finished weights they are my first choice for AR builds unless I’m focusing on weight.  And it will come as no surprise to anyone that Magpul pmags are my only choice for my AR and LR platforms.  And because Magpul really failed to market it well enough, any of the furniture that Magpul put out in the sand color were designed to take Rit Dyes.  There’s an excellent article about that over on GunMag Warehouse’s website at https://gunmagwarehouse.com/blog/ritdye_Sand_Pmags/.  And finally, we talked about the demise of the dust cover.  Traditionally, the feed lips on the top of the mag were a very common wear point.  Those lips spreading would make a magazine useless and it was very hard to tell they’d spread enough to cause them to fail. Trust me, I’ve bought my share of Korean M14 mags and I’m very familiar.  The material used in the pmags removed that fail point in their mags.  So, keeping pmags fully loaded in storage won’t affect their useful life.  I would still recommend using dust covers on mags you keep loaded in long term storage because, well honestly, dust. Needing to keep the rounds from pressing on the feed lips and bending them just won’t happen on pmags. But keeping dust and sand out of them will keep that out of your rifle and gumming up that system.

            One of my first builds, and one that turned into my truck rifle, made use of Adams Arm’s piston conversion kit.  When I built this rifle Adams Arms’ kit had only been out for a couple of years. Then, the only option had a gas block that was the same height as the receiver and had an adjustable gas piston system. And that will tell you how long this rifle has been knocking around in the back of my truck.  I’ve yet to have the piston system fail. Since then, they’ve introduced a low-profile gas block version that comes in either an adjustable version or a fixed version.  I am tempted to get their fixed low-profile gas block version and see how it stands up to life knocking around in a truck.  When I first put this on my rifle I had a hard time getting the information that I needed to make sure that the piston arm had free clearance to travel back and forth, and then finding a hand guard that fit that. Since then, the sheer number of handguards that are available on the market has increased so much that finding a free float or standard hand guard that will accommodate the piston arm has ceased to be a problem. The only complaint that I have with the Adams Arms is the bolt spring that they have.  This keeps the bolt from sitting locked in the receiver. Since I keep the rifle stored broken down, I have to be conscious of using my thumb to keep the BCG pressed in when mating the upper and lower. Otherwise, I’m banging the BCG into the lower. Talking with their rep at NRA AM, she did say that you can run the system without that bolt spring, and many people have, but it might drag a bit when operating.

            Speaking of my truck rifle. That was the first build that I used AeroPrecision’s upper and lower on.  At the time, all the research I did showed that there were only a handful of actual AR receiver manufacturers. Everyone else contracted to have their name stamped on the side. AeroPrecision of one of those handful and they had an option to have the PDQ ambi-bolt release lever preinstalled on their lower.  More on that later.  That upper and lower, bought at separate times, had an amazingly tight mating. I was impressed with their machining and finishing and honestly, they’ve been practically the only choice on my builds since then.  They’ve introduced an integral free float handguard mounting platform on their uppers that makes installing a free float handguard a breeze. No more trying to get the gas tube timed right. Everything bolts right up, no muss, no fuss. One of my next builds will definitely use one of these enhanced uppers.  The rep told me they’re doing something like an open source spec for these and there’s already a couple of manufacturers who are going free floats for this system.

            KNS Precision Inc. has for a long time now been my go to for all pins and small parts for my AR builds.  There’s definitely a school of thought out there that believes that those pins are those pins and pins are pins are pins.  I’ll preface this with saying this is totally anecdotal, but I’ve replaced enough broken trigger pins on ranges of OTHER peoples’ AR’s that having never had any KNS pins fail on me is cheap peace of mind.  I talked with the owner of KNS for a good amount of time on Saturday.  We covered their new AK stuff which include the pins as well as adapters for folding stocks and an improved piston for the gas system.  They also have a quick disconnect take down pin that I will be picking up and running a torture test on. 

            On my most recent .308 build I used Diamondhead USA VRS T-308 handguard.  Aesthetically, I liked the look of the handguard with matching flash hider. Since I bought this they’ve improved the ergonomics on the VR series of handguards and introduced a wider range on those handguards.  I liked the amount of mounting options their handguards give you. There are plenty of either KeyMod or MLok mounting points to put anything you want in the most comfortable position for you on the rifle.  They also do backup sights, compensators, and gas blocks, but I honestly don’t have any experience with either of those and as such really don’t have an opinion on them.

            I had enough time to swing by Barretts booth and talked to them. There are no real new systems coming from them that they’d admit to but there are upgrades and improvements to the buffer system on their M82 rifles that will have me sending mine in for a PMS check and overhaul.

            The rest of the day and Sunday, I just spent wandering around looking for anything that would just out at me as “The New Thing” ™.  Unfortunately, nothing really jumped out at me in that arena. Maybe next year.  But that’s the thing with the AR platform. There’s been sixty some odd years of improvement on this platform. It’s going to be a hard hurdle to clear to supersede it.  Until that phased plasma rifle in the 40-watt range comes out I’ll happily keep playing with the AR.

NRAAM 2018 – The NRA and me, a rocky relationship.

This year was my first time attending the NRA’s Annual Meeting. Not knowing what to expect I think I was pretty free of any preconceived notions as to what to expect.  

But first, let me get you some background about my relationship with the NRA.  Way back when I first started becoming aware of our 2^nd amendment right and as a consequence worried about protecting it, I saw the NRA as an easy, maybe “slack-tivist”, way of doing something about it.  So, I joined, just your basic membership. Back then though, I pretty quickly came to the conclusion that for me the NRA wasn’t being proactive enough, not being strong enough, not really fighting hard enough protecting our 2^nd rights.  So, I joined the GOA (Gun Owners of America) and the SAF (Second Amendment Foundation) because I could see those two groups actually doing things and going to court to protect our rights, and I let my NRA membership lapse. I was not happy with giving up an inch while waiting for the next mile to disappear.

Fast forward to the Parkland H. S. shooting and the birth of Herr Hogg and his spoiled child activism. It was pretty plain at this point that the masks were off and the grabbers were finally open that yes, they were coming for our guns. And while my opinion on the NRA hadn’t changed a lot over the years, they were making the right motions to fight back this time. And I decided that I’d better show them that I would back that.  So, I called up the membership people and rejoined at the lifetime level. H’Ray me, right? Well, no. This is really barely one step up from the slacktivism of the hashtag generation out there. But, it is a step. I have started. This first step of standing up and being counted as one of the millions that cares about the preservation of the one right that will ensure that all the other are safe. Because I firmly believe that the 2^nd isn’t about hunting, nor is it about defense of life and limb. It is ultimately about keeping the Hitler’s and Stalin’s and Pol Pot’s from herding us up into the gulags and concentration camps. Look at history and you will see that taking the means of self-defense out of the common people’s hands always, ALWAYS precedes the genocides. And you can sit in your suburban middle-class home and scoff at that but ask a Ukrainian farmer in the 1930’s how impossible it would be to starve to death while producing bumper crops of wheat.

I’m not going to tell you what my plans are beyond being a lifetime NRA member. I mostly don’t know what they are anyway, maybe looking into getting NRA instructor training or range safety officer training.

We all have our own reasons for what we do and believe.  Please go to https://www.nrablog.com/ and make your own decisions on why you should join.

Range day and new equipment review.

Seeing as how it's about time for my biannual (semi-annual?) blog post I thought I'd just do it about today's range day. 

So, July 28th... in Texas. It's a lovely, partly cloudy day, light winds out of the north keeping the temp down to a mild 102F. But it's a dry heat. Which only means you have to bring cooking spray when you fry the egg on the sidewalk. I shot XTac green tip for the AR and 1945 surplus 8mm Mauser for the Mauser. 

I had three tasks today. Rezero my truck rifle, test shoot my 104 year old Mauser G98AZ to make sure the stock repair holds, and test this new mag from CAA out. 

This new mag, the CAA CDMag, is a polymer mag like PMags but has an actual round counter on the rear of the mag. The round counter is color coded as well as numbered so quick checks for ammo remaining can easily see a green, yellow or red background. Top 10 rounds have a green background, rounds 11 - 20 are yellow and the last 10 have a red background. The round counter worked like a charm but it was sized so that you saw 2 numbers in the window. The top visible number being the actual rounds remaining. 

Loading was only slightly harder than loading a PMag. It locked up into the magwell solidly with very little wiggle either fore/aft or side to side. Which may be why it wouldn't drop free when the mag release was hit. Unloaded it would spring about 2 inches when the release was hit, but wouldn't move on its own at all when loaded full. And only pop enough to say it it was out of locked on a half mag. My guess is the mag bulges slightly when loaded and that's why it's not moving when loaded even though it's heavier with 30 rounds. 

Aside from a problem stripping off the first round of a fully loaded mag (it took 3 tries to finally grab that first round) it worked flawlessly and locked open without trouble on the empty mag. 

They retail about 8 bucks more than the windowed PMags. I'm gonna continue to use this as a range mag to see if use will work it in better.  I would like to see the round counter window sized a bit better so it only showed one number but I can see why it's like it is. I'd also like to see it sized better so it drops free in its own. But that's my personal preference. I know others who prefer the tighter seating. The failure to feed the first round I'm gonna reserve judgement on till I've used it more to see if it's just a quirk of a brand new mag or not. As it stands now they aren't worth it to me to switch over from PMags as my default mag, but they do make a good range mag. 

As for the other two tasks. It'd been maybe 5 years since I'd sighted in my truck rifle, an AeroPrecision AR-15 with an Adams Arms piston conversion kit, Trijicon ACOG TA-31H scope, and magpul furniture. I shot it a couple of months ago and I was 3 ft. high and about 2 ft. left at 100 meters. So... yeah. 

Zeroing was done kneeling, semi supported. Once I got it on paper, thanks for the spotting Old_NFO,  I adjusted till I hit consistently in that group at 5-5:30. Then tweaked it to that group in the red. The group up at 3 to 4 high were when I moved back to 100 meters. Which is where it should be for a 25/250 battlefield zero. The larger holes are from the Mauser, again at 100. 15 rounds of mule kicking 8mm Mauser and the stock repair held wonderfully. 

Here's a pic of Obi Wan Kenobi sleeping for sticking around thru this blog. 

All I all not a bad day at the range. 

- Posted using BlogPress from my iPhone

Sent from my iPhone. 

It follows me home and be my presciousessesssssss

So yesterday, in a fit of pure evil the color of the blackest politician's heart, Old NFO forced me to go to the local bugscuffleville gun store. And then at virtual gunpoint, coerced me to put a 1916 SMLE No. 1 Mk III* on layaway. But it gets worse!  Then, in what can only be the most diabolical of plots with the owner had said owner "mistakenly" charge my card not the layaway amount, but the remainder!  They then were able to hide that from me till too late last night. Upon discovery of this most dastardly conspiracy, I was left with no other option than to pick the rifle up today. And finally to add insult to injury, there was CCI Mini-Mag .22lr on the counter and some of that found it's way into the bag.

That's my story and I'm sticking to it. 

Range day weirdness.

First off, sorry for the sparse posting.

Today was .30-06 day at the range.  Well, to be more specific it was WW1 rifle .30-06 day at the range.

So, I dug out my Springfield 1903(a3). (I haven't found a decent shooter 03 yet.) My Eddystone M1917 and a Winchester made Eddystone that I'd bought from a friend a while back but never had out to the range.

I needed to get the 03 sighted in and so I picked it up first.  And had it nicely sighted in 6 rounds at 50 yd.  I was thankful for the a3 rear sight rather than the older ladder sight.  I did not want to have to figure out where my POI should be for a 547 yd zero POA. 

Since the only way to adjust the sights on the Eddystone is to take a punch and drift the front sight I was just gonna make sure they were pretty much where they should be and then plink away till I was happy.  My Eddystone Eddystone shot pretty much as expected and was a might bit right of dead center. 

When I pulled out the Winchester I was nowhere on paper when I checked after the first shot.  Just to make sure I wasn't pulling it something I fired a couple more carefully and nothing.  Just a really nice unmarked target.  So, I walked up closer (between 15 and 25 yd.) and fired a round.  Then a couple more just to make sure I was seeing what I was seeing.

This is what I got.

Yep, four rounds from between 15 and 25 yds and this is what I got. Keyholing like nobody's business.  Took the rifle back to the loading bench and inspected it as best I could.  Throat and muzzle looked okay.  The crown was undamaged. The brass from the fired shells were undamaged.  The rounds fed, extracted and ejected without a problem.  I checked the muzzle gauge with another round. 

That's not too bad really. I obviously don't have a .30 cal gauge to get an accurate measurement.  Talked with my captive gun smith, who I'd bought the rifle from and we're both stumped.  Next is a visit to my local smith and have it checked out.

Fun day anyway.

New Build Complete

Just got the hand guard in today. Many thanks to DiamondHead USA for exchanging the low hand guard for their new high hand guard with no problems or hassle.

.308 built up on an AR platform using AeroPrecision's M-5 Lower and upper, heavy profile barrel, Magpul MOE buttstock, MIAD grip with spare battery insert, Diamondhead USA VRS hand guard and matching T-Brake Muzzle Compensator. I went with my go to KNS trigger pin set and Geissele SSA-E trigger. I just like them. I pulled the Burris scope off of my AR Varmitter. It was too much scope for that caliber anyway. I'm gonna put a bipod on it tomorrow when the adapter for the key-mod comes in.

Gun Pron and Range Report

So a couple of weeks ago I threw a throw away bid on a Glock 36 on Gunbroker. The bid was really low and there was a week to go on the auction so I didn't even remember it after a couple of days.  But to my surprise I won it. Warning, pic heavy, for me anyway.

This:

to be precise.

Picked it up today and went to the range to test it out.  It is a seriously different trigger from the 1911's I'm used to.

I started with the lower left target and proceeded to curse the inventor of the striker fire trigger. But 50 rounds and 5 targets later I got that group on the upper right target.

The next 50 rounds I shot just to make sure I understood the difference in the feel and break of a striker fire trigger. Really, it's just so mushy from what I'm used to in a trigger.  Even compared to some of my revolvers.

And I swear it broke in a different place almost every time. I'm still anticipating the recoil as little as it is. But I'm pretty out of practice with handguns of late. I've been concentrating a bit too much on rifles over the summer.

And this:

will drive as many people as possible crazy.  I know you're cringing right now, Curtis, Daniel, Fudd, FarmDad, well the list goes on and on. :D

That's curious

You know, of all the rifle builds I've done. I still haven't done a free float handguard.

Idle bets and range reports

So, when you're sitting around, as you do, and you make the comment that you bet you could build an entire AR just from the spare parts in your boxes...

Don't.

Because when you do, you'll end up with this:

Except you'll realize that you don't have, of all things, trigger guards and a good Magpul pistol grip.  I mean seriously.  How did I not have any trigger guards. I swear I have pulled a bazillion of those things off of builds I've done and where are they? Pistol grips I have. I have more than a dozen stock GI grips, but I really hate those things.

And this is what the zeroing looks like.

 

 

The far right is the first shot I took, from the hip by the way, because if it was going to blow up, I'd rather keep my nose.  Aimed shot number one was far lower left. Shot two was upper left. I miscounted and had a bit of trouble feeling the clicks on the EOTech. That little group at the 5 o'clock inside the "10" ring holds shot number 3 and then the other 3 holes in the ten ring were to confirm the zero.

So, the lesson for today is maybe have a better idea of what you've got in your parts bins.

Also, I got another 200 rounds through the AK today while I was there. Had a failure to feed on round three of magazine #2 today. It just didn't strip the round off the top of the mag. Cycled the charging handle and continued to bang away.  That makes 2 malfunction in 1200 rounds, the FTF today and the weird double feed I had in the first 300 rounds.  Not bad for something that I haven't cleaned, only lightly LIGHTLY oiled it after I picked it up from the smiff, and been running el cheapo wolf lacquer coated steel cased milsurp ammo through it.

I stopped there, because it was literally too hot to handle the rifle or mags.

It was a good day.
 

15 hours and counting.

Do you realize how incredible this is? And this isn't even the fastest man made object we've sent out.

http://pluto.jhuapl.edu/

AK Range report.

Okay. So, I'm now about 500 rounds into the test run.  Another 500-1000 to go depending on how well I can survive the heat.  I got it rough sighted in last week and put a couple of hundred rounds through it. Today I finished tweaking the sights so they were as spot on as my tired ol' eyes can get it. Then finished the first box of 500 I had with me.

I actually got a FTF today I had about 100-120 rounds left out of the box and on the second round of a topped off 30 round magazine I had the round hang up and hold the bolt back about half way.

Yes, I know. AK's never jam.  Whatever.  This was bad enough I had to drop the mag and pop the dust cover off to get the round out from behind the bolt.

So, 500 rounds through, not been cleaned or oiled since I put a light, LIGHT coat of hopes on it after I first got it and 1 malf so far.  I've had AR's perform better.  Just saying.

I do have to say that Randy Kline, the gun smith at Jacksonville, TX who put it together, did an excellent job and the trigger is one of the smoothest I've ever had on a military rifle.  I highly recommend him for AK and FAL work.

I'll try to get the next 500 rounds put through it over the weekend if possible.  But it's slow going.  That rifle heats up enough that I can't hold onto the front grips without asbestos gloves after barely 100 rounds.  I had the thing literally smoking today, even with long breaks between magazines to let it cool down.
 

My new pretty.

Well, not pretty in the least. It's a Polish under folder kit (less the parts needed to make it 922r compliant), a NoDak receiver, and the smiffy magic of Randy in Jacksonville, TX. The kit is a numbers matching kit from a demilled Polish AK, with all the wear you'd expect from an ex-military rifle.







- Posted using BlogPress from my iPhone

Yes, I'm doing a gun review. The DP-12 by Std. Mfg. LLC of New Britain, CT.

Today we're going to look at the DP-12 by Standard Mfg. of New Britain, Connecticut. 

Std Mfg DP-12

It's the new large capacity bullpup shotgun on the market. Set to go up against the UTAS UTS-15 and Kel-Tec's KSG, it's approaching the idea from a new direction. Rather than two tubes feeding a single chamber, they basically took two shotguns and melded them together. It's chambered to 3" so any 12 gauge ammo you can find will fire from it, but I'd test any short shells before using them.

Initial impressions were that this is a well constructed, robust shotgun. The balance when unloaded is biased to the aft. I don't know if this was intentional or not, but when loaded it has a nice center of gravity. There's plenty of rail on top for mounting optics, lasers, etc.  I just put a cheap red dot for range testing today and it worked fairly well.  The controls are logical and follow the basic AR setup. They're also ambidextrous. The slide lock is on front of the trigger guard and easily reachable and usable by the trigger finger. The front pistol grip comes standard on the shotgun and is solid to the slide. Something that's looking to be a problem with the Kel-Tec and a couple of incidents of self inflicted wounds when the front pistol grip has come off when racking.  The loading/ejection port is open and easy to inspect.

Loading is straight forward and easy. Racking the slide back allows you to load the barrels and sliding it forward closes the ramps and loading the magazine tubes is easy. Also, these tubes truly hold 7 3" rounds each. Unlike the KSG or the UTS which kinda/sorta holds 7 rounds of 2 3/4" shells if you really cram them in.

Firing is easy and the follow on shot is quick.  Recoil is very manageable. Loads from 2 3/4" bird shot up through a couple of 3" turkey loads really had very little difference. Part of this maybe the weight, it's basically two pump shotguns you're carrying. But the recoil was still fairly straight back with very little muzzle climb.

Racking is easy and forgiving. One doesn't need to slam it back and forth to get it to work unlike the UTS. It will take a little training to get used to the Bang-Bang-Chunk action since the slide won't unlock till both barrels are fired.

As mentioned above, the follow on shot is quick due to the double barrel configuration, and the slide throw is not too long.

All in all it's a nice shotgun to shoot.  Now keep in mind this is not your grandfather's turkey gun or the next big thing in skeet/trap shooting.  This is a compact maneuverable shotgun that holds enough rounds to keep your worst nightmares at bay. In other words, this is a great home defense shot gun. It's short enough that you can swing it around in hallways or doorways with out any difficulty while still carrying enough rounds to deal with the threat.

There are some things that I'm not too fond of.  First off, the weight. Like I said it's basically two pump shotguns in one frame and while I can't say that it's double the weight of the UTS or KSG, it is definitely heavier by a few pounds loaded or unloaded.

The safety is familiar but lacks that positive lock in position that I'd like to feel when moving it.  Currently it just rotates to the stop without locking into position once it's there. The other big issue I have with the safety is that it wont move to safe if only one chamber has been fired and the other one is still "hot". Which means you'll have to fire twice no matter what or manually release the slide and eject one live round with one spent to get the safety into the safe position.

The shotgun has no way of knowing if the chamber is loaded or empty.  Say you load 6 rounds in one tube and only 4 in the other.  You'll end up at some point with one chamber empty and depending on which one it is you'll get a click-bang or bang-click before the slide will unlock and you can rack the next round(s).

There is no "field stripping" this shotgun. You need a couple of allen wrenches to disassemble it. I'm a big believer that you should be able to do basic cleaning of any gun without having to resort to a gunsmith's bench to do it.

And finally, the price. Currently they're only available from CheaperThanDirt.com and they're retailing at $1395.00 each. Hopefully they will come down as they get more of them out there, but CTD bought the first 30,000 units so, don't expect other vendors or a price change anytime soon.

I hope that Std. Mfg. addresses the safety issue. You should be able to put the shotgun on safe even if you don't fire both barrels.  As for the safety feel and the one empty chamber issues, while they would be nice to solve, I won't lose any sleep over them.

So, I give this shotgun a thumbs up. It's got a good beat and you can dance to it.
 

I need to organize

Today I found out my rifles are chambered in this:


I didn't realize it was that many. But in my defense the first five were developed over 120 years ago.
 

And so it shall be written.

When I write my autobiography, I shall have flame throwers and hover boots.

About that curtailed purchasing...

Okay, so I really didn't curtail it that much. But I did... a bit... honest... I can quit anytime I want. Stop laughing! I can quit!

Anyway, I started saving up for a major purchase a ways back. I mentioned it in this post back in May.

The following are pics of my brand new to me, FBI Thompson M1928A1 with original case, manual and drum magazines.

Except it looks a lot like a helicopter.

It's still in transit. The gentleman transporting it from Florida to me is being kind enough to store it temporarily till I can find a hanger here for it.  There's no way I'm going to even risk a chance of hail damage to it. I'm not saying I'm all school girl, jumping around, clapping, squealing excited right now... All those years flying fixed wing and jets and I still wanted to do this. Well, I'm gonna and mom and dad can't stop me now. If they ask, I'll just tell them I'm playing piano at a whore house.

I've lined up an instructor and contacts with several other owners in the area. So, the support network is starting at least.  Having time off is an issue.

Honest, it followed me home on it's own...

Can I keep it? Too late, I already am.

She's a 1941 Kovrov SVT-40. Has the SVT not AVT stock. (No cut out for the full auto flip on the safety switch.) Really in great shape for a 70+ year old gun.

Range report will follow when time allows.

I've heard this gun referred to as the Soviet Garand. I think it has a bit more in common with the US's M14 and would make it a more advanced rifle than the Garand. The notable feature being the detachable magazine. But as both the Garand and the SVT-40 were WW2 and the M14 was a development of a decade later, I can see why the one comparison and not the other.

This rifle was planned to be the replacement for the Mosin Nagant and be the primary MBR of the Soviet military but the timing of the war, vulnerability of the factories making these to the Nazi advance during Operation Barbarosa, and just the flat out critical need for millions of rifles NOW, meant the Mosin Nagant remained the primary rifle of the Soviets during WW2 and relatively few of these being produced in comparison.  And we all know the AK pretty much eclipsed anything else coming before it after the war.

I'm thinking about naming her Ivana Onnatop.

Conversations we have.

Me: You know what I learned yesterday! Children are hereditary. If your parents don't have kids, you're more likely not to have them either!

Daniels: I.. Don't... Think... It... Works... That... Way.

Desi: I heard it skips a generation.

Here, have a clue. Free of charge.

Everyone keeps referencing al-Qaeda when they talk about ISIS or ISIL.  Has it gone over their heads that comparing al-Qaeda, a terrorist group operating in small groups with no easily visible support or logistics train, with ISIS, a group that has grabbed territory, is collecting taxes from towns and people in it's area of operations, has seized operating oil wells and refineries and is trading oil on the OPEC markets, is seizing infrastructure like electricity, water as well as logistic points like ports and airfields, is consolidating borders and expanding them, have as much in common as apples and oranges?